bst2222全球奢华游戏公司_bst2255全球奢华游戏_贝斯特全球最奢游戏2222

bst2222全球奢华游戏公司
热线电话:400-879-1999 山汽官方微信
郑重声明 购机 售后
在线询价
热线电话:400-879-1999
您现在所在的位置: 首页> 新闻资讯 > 行业新闻 >

自动上料搅拌机施工的各部位操作

所属分类:行业新闻 发布时间:2021-02-26 来源: 浏览量:18

1.搅拌车搅拌筒的旋转由液压马达通过专用行星减速机带动,行星减速机的输出轴可以实现一定角度的摆动,以满足恶劣路况下搅拌筒的跳动。
1. The rotation of the mixer drum is driven by the hydraulic motor through a special planetary reducer. The output shaft of the planetary reducer can realize a certain angle swing to meet the beating of the mixer drum under bad road conditions.
2.液压系统采用恒功率变量柱塞泵,减少发动机的功率损耗。
2. Constant power variable piston pump is used in the hydraulic system to reduce the power loss of the engine.
3.进水系统可根据计量设定实现自动进水。
3. The water inlet system can automatically feed water according to the metering setting.
4.干料上料,按照设计好的配比由铲臂、动臂缸、定量的料斗自动上料。
4. Dry material feeding: according to the designed proportion, it is automatically fed by shovel arm, boom cylinder and quantitative hopper.
自动上料搅拌机
5.自动上料搅拌车搅拌筒内壁上设置双螺旋形叶片,正向旋转为进料、混凝土搅拌;反向旋转,在螺旋叶片的推动下、混凝土由出料口出料。
5. Double spiral blades are set on the inner wall of the mixing drum of the automatic feeding mixer, which rotate in the positive direction for feeding and concrete mixing; in the reverse direction, the concrete is discharged from the discharge port under the push of the spiral blades.
6.行走系统由发动机通过液力变矩器、前后传动轴到前后桥。本发明采用前后双桥驱动形式。采用液力变矩器减少对发动机的冲击、延长了发动机的寿命。
6. The traveling system is composed of engine, front and rear transmission shafts and front and rear axles. The invention adopts a front and rear double axle driving form. The hydraulic torque converter is used to reduce the impact on the engine and prolong the service life of the engine.
换油:搅拌机一般每半年需要更换一次润滑油,润滑油的型号为32#机械油,换油时,小心拧开油塞,放进其内存油,注意油枪内可能会有剩余的内压,以防油的喷射。
Oil change: generally, the blender needs to change the lubricating oil every six months. The type of lubricating oil is 32 # machine oil. When changing the oil, carefully open the oil plug and put the oil in the blender. Pay attention to the residual internal pressure in the oil gun to prevent the oil from spraying.
轴承润滑脂:一般大修时更换一次,润滑脂量为轴承腔间隙1/3-1/2,润滑脂推荐采用高温钙纳基润滑脂。
Bearing grease: it should be replaced once in general overhaul, and the amount of grease should be 1 / 3-1 / 2 of the bearing cavity clearance. High temperature calcium base grease is recommended.
搅拌机的泄露保护处理:假如渗漏开关保护,表示电机侧的机械密封损坏,必须要检查和修理,打开油室腔的堵塞,排尽其内积液。
Leakage protection treatment of mixer: if the leakage switch is protected, it means that the mechanical seal on the motor side is damaged. It must be checked and repaired. Open the blockage in the oil chamber and drain the liquid in it.
热门产品 / HOT PRODUCT

 

首页 产品 电话 置顶
Baidu
sogou